net_if_ipv6_calc_reachable_time() in subsys/net/ip/net_if.c derives a randomized ND reachable time from ipv6->base_reachable_time as min_reachable + sys_rand32_get() % (max_reachable - min_reachable), where min_reachable = base/2 and max_reachable = 3*base/2 using integer division. When base_reachable_time is 1, both min_reachable and the modulus collapse so the function returns 0, and net_if_ipv6_set_reachable_time() stores that 0 into ipv6->reachable_time. The base_reachable_time is attacker-controlled: handle_ra_input() in subsys/net/ip/ipv6_nbr.c accepts the Reachable Time field of an incoming Router Advertisement whenever it is nonzero and <= MAX_REACHABLE_TIME, so a single unauthenticated, link-local RA carrying a Reachable Time of 1 drives the computed reachable time to 0. Router Advertisements are unauthenticated by default and require only adjacency to the target link. When a neighbor is subsequently confirmed reachable, net_ipv6_nbr_set_reachable_timer() reads the value and executes NET_ASSERT(time, "Zero reachable timeout!"). On builds with CONFIG_ASSERT enabled this triggers a fatal kernel assertion — a remote denial of service; on builds without assertions the reachable timer is armed with K_MSEC(0) and fires immediately, forcing reachable neighbors into perpetual re-solicitation (STALE), degrading Neighbor Discovery. The impact is limited to availability; there is no memory-safety, confidentiality, or integrity consequence.

The ITE IT82xx2 USB device-controller driver (drivers/usb/udc/udc_it82xx2.c) mishandles multi-packet OUT transfers on non-control endpoints. In work_handler_out() the active transfer buffer is obtained with udc_buf_peek() (which does not dequeue it); when a full max-packet-size packet arrives but the buffer still has tailroom (the transfer is not yet complete), the pre-fix code both re-arms the endpoint to keep filling that same buf via work_handler_xfer_continue() and simultaneously hands the same, still-being-filled buffer to the upper stack with udc_submit_ep_event(). Because udc_submit_ep_event() transfers ownership of the buffer to the USB device stack (usbd_event_carrier() appends &buf->node to uds_ctx->ep_events, after which the class handler processes and net_buf_unref()s it), the driver continues to DMA subsequent host-controlled OUT packets into a buffer the upper stack may already have freed and recycled — a use-after-free write. In addition, since the buffer was never dequeued, the completing packet runs udc_buf_get() on the same object and submits it a second time, appending &buf->node to the event slist twice (singly-linked-list corruption) and causing a double net_buf_unref(). The IT82xx2 is a USB peripheral controller, so the untrusted USB host controls OUT-transfer packetization and can force this path against any non-control OUT endpoint whose queued buffer exceeds one packet — an ordinary bulk/interrupt pattern. The driver and USB device stack run in kernel context above the external host, giving the host a device-side kernel heap-corruption primitive: a reliable denial of service and, because the written bytes are attacker-controlled, plausible corruption of adjacent net_buf pool memory. The vector is physical (USB attach). The fix defers submission until the buffer is completely filled and lets xfer_work_handler() drive continuation, so each OUT buffer is submitted to the upper stack exactly once.

The ITE it51xxx I2C driver, when operating as an I2C target (slave) in buffer mode (CONFIG_I2C_TARGET + CONFIG_I2C_TARGET_BUFFER_MODE), copies host-supplied write data into the fixed-size data->target_in_buffer inside its target FIFO interrupt handler target_i2c_isr_fifo() in drivers/i2c/i2c_ite_it51xxx.c. The copy loop stores to target_in_buffer[i + data->w_index] and only checks data->w_index against sizeof(data->target_in_buffer) after the write has already completed, so the bounds check cannot prevent the overflow. The running index data->w_index accumulates count bytes on every FIFO-fill interrupt of an ongoing transaction and is reset to zero only on a STOP or timeout condition. An I2C host that streams a single write transaction longer than the buffer (default CONFIG_I2C_TARGET_IT51XXX_MAX_BUF_SIZE = 256 bytes) drives data->w_index past the end of the buffer, and each subsequent host byte is written out of bounds into the adjacent data->target_out_buffer and following static device data. The trigger is a malicious or misbehaving I2C master on the same bus (for example a compromised application processor or a rogue device on an exposed I2C bus); no software privilege on the victim is required and the handler runs in the target's kernel/firmware context. Because both the written values and the overflow length are attacker-controlled, this is an out-of-bounds write that can crash the controller or be shaped toward code execution. The fix adds a pre-write bounds check in target_i2c_fifo_read_to_buf() that aborts and resets the FIFO before any out-of-bounds store.

The Zephyr SDIO subsystem function sdio_io_rw_extended_helper() in subsys/sd/sdio.c finishes transfers with a byte-I/O loop that uses size = MIN(remaining, func->cis.max_blk_size) as the per-iteration step. The value func->cis.max_blk_size is decoded directly from the SDIO card's CIS FUNCE tuple in sdio_decode_cis() and is not validated. When a card reports a maximum block size of zero, size is always 0, remaining never decreases, and the loop spins forever. The loop is reached from the public SDIO client API used by drivers, including sdio_read_fifo(), sdio_write_fifo(), and the incrementing register read/write helpers, each of which enters the loop while holding the per-card mutex func->card->lock. A card advertising max_blk_size == 0 therefore hangs the calling thread permanently on its first non-block-aligned transfer and never releases the mutex, denying service to the SDIO peripheral (and any subsystem such as Wi-Fi that depends on it) until the device is reset. The malicious value must come from the SDIO card itself, so the defect is exploitable where a removable SDIO/combo card slot lets an attacker insert a crafted or malfunctioning card (a physical attack vector); on boards with a soldered SDIO peripheral it is not attacker-influenceable. There is no memory-safety, confidentiality, or integrity impact — only a permanent availability loss. The fix returns -EIO when func->cis.max_blk_size is zero, before the loop is entered.

The mcumgr SMP settings-management group handlers settings_mgmt_read(), settings_mgmt_write(), and settings_mgmt_delete() in subsys/mgmt/mcumgr/grp/settings_mgmt/src/settings_mgmt.c allocate a key_name buffer (and, for read, a data buffer) via k_malloc() when CONFIG_MCUMGR_GRP_SETTINGS_BUFFER_TYPE_HEAP is enabled, relying on the end: label to k_free() them. When CONFIG_MCUMGR_GRP_SETTINGS_ACCESS_HOOK is also enabled and the application access hook rejects a request by returning status MGMT_CB_ERROR_RC, the handler executed return ret_rc; directly, bypassing end: and leaking the heap allocation on every rejected request. The settings handlers are reachable over the unauthenticated SMP transport (Bluetooth LE, UART, or UDP, depending on product configuration). The access hook is the mechanism applications use to deny unauthorized settings access, and MGMT_CB_ERROR_RC is a common rejection style, so an attacker who can send settings read/write/delete commands that the hook rejects triggers a heap leak on each attempt. Because the leaked memory is never reclaimed until reboot, a sustained stream of rejected requests monotonically exhausts the kernel heap until k_malloc() fails, denying mcumgr service and impacting any other heap consumer on the device — a denial of service. The impact is availability-only; there is no memory corruption or information disclosure. Only configurations that select the heap buffer type, enable the access hook, and register a hook that returns MGMT_CB_ERROR_RC are affected (the default stack buffer type cannot leak).

The MQTT-SN client keepalive handler process_ping() in subsys/net/lib/mqtt_sn/mqtt_sn.c removes the gateway record after PINGREQ retries are exhausted. It invoked SYS_SLIST_PEEK_HEAD_CONTAINER(&client->gateways, gw, next) but discarded the result. That macro is a pure expression that does not assign to gw, so gw retained its NULL initializer regardless of the list contents. The code then dereferences the NULL gw (gw->gw_id) and passes it to mqtt_sn_gw_destroy(), reaching k_mem_slab_free(&gateways, NULL). With CONFIG_MEM_SLAB_POINTER_VALIDATE enabled this triggers k_panic(); in the default configuration it performs a write through the NULL pointer ((char )mem = slab->free_list;) and corrupts the slab free list. The outcome is a crash/kernel panic or, on targets where address 0 is writable, silent memory-allocator corruption. The vulnerable branch runs whenever the connected MQTT-SN gateway fails to answer keepalive PINGREQs for the configured number of retries. This condition is controlled by the remote peer: a malicious or compromised gateway, or an on-path/adjacent attacker that advertises itself as a gateway and then stops responding (or blackholes the real gateway's PINGRESPs), forces the client into the defect. MQTT-SN runs over UDP and no authentication is required. The impact is a remotely triggerable denial of service (availability) of the affected MQTT-SN client; there is no attacker-controlled data written. The sibling remover process_advertise() uses SYS_SLIST_FOR_EACH_CONTAINER_SAFE and is not affected. The fix assigns the macro's return value to gw.

The Sierra Wireless HL78xx modem GNSS driver (drivers/modem/hl78xx/, later drivers/modem/vendor_standalone/hl78xx/) embeds a generic struct gnss_nmea0183_match_data match_data inside struct hl78xx_gnss_data. The generic NMEA0183 match helper (drivers/gnss/gnss_nmea0183_match.c) requires that context to be the first member because its callbacks cast user_data directly to struct gnss_nmea0183_match_data . In the affected releases match_data was the second member (after const struct device dev), so it sat at a non-zero offset while gnss_nmea0183_match_init() initialized it at the correct address. The registered NMEA handlers instead pass the whole device data object (data->devices.gnss->data, offset 0), producing an offset-shifted type confusion between where state is initialized and where the parse callbacks read and write it. When NMEA sentences from the GNSS receiver are parsed, the GGA/RMC callbacks write parsed fix data into the wrong location within the struct, and the GSV callback (gnss_nmea0183_match_gsv_callback, active under CONFIG_GNSS_SATELLITES) reads its satellites pointer and bound from the wrong offsets — non-pointer bytes of struct hl78xx_gnss_data — and then writes parsed struct gnss_satellite entries through that bogus pointer. This is a write through an uninitialized/wild pointer with a garbage bound. The NMEA handlers are registered by default (CONFIG_HL78XX_GNSS_SOURCE_NMEA is the default GNSS source) on devices using the HL78xx GNSS. The driver runs in kernel context and the NMEA data originates from the GNSS radio front-end, so a party able to influence the GNSS signal (for example GNSS/GPS spoofing at radio proximity) can drive the kernel-side parser into the faulty write. The most likely impact is a crash (denial of service) because the bogus pointer resolves to a fixed near-NULL value, with adjacent-memory corruption possible on MMU-less targets. Confidentiality is not affected. Exploitation requires the satellites feature to be enabled and active, so attack complexity is high.

The Bluetooth Classic (BR/EDR) L2CAP receive handler bt_l2cap_br_recv() in subsys/bluetooth/host/classic/l2cap_br.c dispatched inbound data PDUs based only on the destination channel ID, without checking that the target channel had reached the BT_L2CAP_CONNECTED state. A dynamic channel is assigned its RX CID and added to the connection's channel list while still in BT_L2CAP_CONNECTING (and later BT_L2CAP_CONFIG) — before configuration completes and, for PSMs that require security, before the peer is authenticated (l2cap_br_conn_req()). Because the channel is already findable by bt_l2cap_br_lookup_rx_cid() during this window, a remote peer within radio range can send a data PDU addressed to that CID and have it processed on a not-yet-established channel. The dispatch keys off channel fields (BR_CHAN(chan)->rx.mode, rx.mps) that are only initialized during configuration by l2cap_br_conf(); since channel objects are pooled and bt_l2cap_br_chan_del() does not reset rx.mode or the reassembly buffer _sdu, a reused channel can carry stale state into the CONNECTING window and route the frame into the retransmission/flow-control path (bt_l2cap_br_ret_fc_recv()) with stale parameters and a possibly stale _sdu pointer. The impact is delivery of attacker data to upper-layer protocol handlers on a half-open (and possibly unauthenticated) channel, plus operation on stale or partially initialized channel state on reused channel objects — leading to channel/link teardown (denial of service) and, in the stale-_sdu case, a dangling-pointer condition. The fix adds an explicit BR_CHAN(chan)->state < BT_L2CAP_CONNECTED guard that drops any data received before the channel is fully connected.

The Silicon Labs SiWx917 WiFi driver's transmit callback siwx91x_send() in drivers/wifi/siwx91x/siwx91x_wifi.c frees a network packet it does not own. In the Zephyr TX path the net_pkt is owned by the L2/networking stack; the driver only borrows it to copy the frame bytes into a local net_buf. Before the fix, after transmitting, siwx91x_send() additionally called net_pkt_unref(pkt) on the caller-owned packet, dropping its last reference and returning it to the shared packet pool prematurely. This code path is compiled in by default (CONFIG_WIFI_SILABS_SIWX91X_NET_STACK_NATIVE). The caller, ethernet_send() in subsys/net/l2/ethernet/ethernet.c, keeps using the packet after the driver returns: it reads net_pkt_get_len(pkt), updates TX statistics, and then performs its own net_pkt_unref(pkt). Because the driver already released the packet, these are use-after-free reads followed by a second unref (a double free). When concurrent network activity recycles the freed slab slot between the two unrefs, the trailing unref decrements a different, live packet's reference count and frees it, corrupting the net_pkt pool shared by both the receive and transmit paths. The defect is exercised by ordinary transmission over the native-stack SiWx917 WiFi interface, and an adjacent attacker on the same WiFi network can induce transmissions (for example ARP or ICMP echo replies, or TCP handshakes) to drive the path. The primary observable impact is loss of availability (transmit hangs and crashes from pool corruption), with race-dependent memory corruption of the kernel networking buffer pool. The fix removes the erroneous net_pkt_unref(pkt) from siwx91x_send(); the driver's receive-path unref, which correctly frees a packet the driver itself allocated, is unaffected.

When Ethernet bridging is enabled (CONFIG_NET_ETHERNET_BRIDGE), eth_bridge_input_process() in subsys/net/l2/ethernet/bridge/bridge_input.c decides how each frame received on a bridge member interface is handled. For frames that must also be delivered to the local stack, the code called eth_bridge_handle_locally() and returned NET_OK. That helper does not consume the packet — it only calls bridge_iface_recv() (via virtual_recv()), which returns NET_CONTINUE without taking ownership of pkt. The NET_OK verdict then propagates through ethernet_recv() up to processing_data() in subsys/net/ip/net_core.c, where NET_OK is interpreted as "the packet was consumed, do not free it." Because no consumer actually took ownership, the RX net_pkt is never returned to the pool and is leaked. The concretely reproducible leak occurs for frames whose EtherType has no registered L3 handler when CONFIG_NET_ETHERNET_FORWARD_UNRECOGNISED_ETHERTYPE is set (default y when CONFIG_NET_SOCKETS_PACKET is enabled): the fall-through L3 dispatch does not overwrite the NET_OK verdict, so ethernet_recv() returns NET_OK and the buffer is never released. Any device on a bridged L2 segment can emit broadcast/multicast frames carrying an arbitrary EtherType with no authentication. Each such frame permanently consumes one buffer from the finite RX pool (CONFIG_NET_PKT_RX_COUNT), so a brief broadcast flood exhausts the pool and the device can no longer receive traffic until it is rebooted — a persistent denial of service. There is no confidentiality or integrity impact. The fix makes eth_bridge_handle_locally() propagate the real net_verdict and return NET_CONTINUE for locally-kept frames, writing the bridge interface back through a new dst_iface out-parameter so the packet follows the normal receive path and is unreferenced exactly once.