The Zephyr Bluetooth LE Audio Basic Audio Profile (BAP) unicast client mishandles peer-supplied ASE state notifications. In unicast_client_ep_qos_state() (subsys/bluetooth/audio/bap_unicast_client.c), the handler writes attacker-controlled QoS fields (interval, framing, phy, sdu, rtn, latency, pd) through the stream-qos pointer with only a stream != NULL guard. stream-qos is NULL for any stream that has been codec-configured via bt_bap_stream_config() but not yet added to a unicast group (it is set only by unicast_group_add_stream()). A malicious or buggy remote ASCS server, to which the local device is connected as a BAP unicast client, can send a GATT notification announcing the ASE has entered the QoS Configured state while the local endpoint is still in the Codec Configured state — a transition the dispatcher explicitly permits — during that window, causing a write through a NULL pointer and a crash (denial of service). The data written is itself remote-controlled. The defect shipped in v4.3.0 and v4.4.0 (and earlier). The fix re-points all BAP QoS storage to the always-valid embedded ep-qos struct, eliminating the NULL dereference.

Zephyr's BSD-sockets getaddrinfo() implementation (subsys/net/lib/sockets/getaddrinfo.c) passes a pointer to a stack-allocated state object (struct getaddrinfo_state ai_state) as the user_data of an asynchronous DNS resolver query. The socket layer waits on a semaphore with a timeout deliberately set slightly longer than the resolver's own per-query timeout. When that semaphore wait nonetheless times out (-EAGAIN) - which can occur when the resolver's timeout work is delayed by workqueue contention, or in the documented multi-retry configuration where CONFIG_NET_SOCKETS_DNS_TIMEOUT exceeds CONFIG_NET_SOCKETS_DNS_BACKOFF_INTERVAL - the pre-fix code retries the query (goto again) without cancelling the previous one and without resetting the semaphore. The previous query slot remains active in the resolver with its callback and the stack pointer as user_data, and ai_state-dns_id is overwritten so the stale query can no longer be cancelled. A subsequent DNS response delivered over UDP and matched by its 16-bit transaction id (in dispatcher_cb()/dns_read()), or the resolver's own delayed query-timeout work, then invokes dns_resolve_cb() against the now out-of-scope stack frame, writing through the stale pointer (state-status, state-idx, state-ai_arr[], and k_sem_give()). Because the triggering response is network-delivered and its 16-bit id is spoofable/replayable by an on- or off-path attacker, this is a network-influenceable use-after-return that can corrupt reused stack memory, leading to crashes/denial of service or memory corruption. The fix cancels the timed-out query by name and type before retrying and resets the local semaphore, eliminating the stale callback path. Affected: Zephyr v4.0.0 through v4.4.0.

The Microchip SERCOM-G1 UART driver (drivers/serial/uart_mchp_sercom_g1.c), used by the PIC32CM-JH SoC family, contains an out-of-bounds write in its asynchronous (DMA) receive path. When uart_rx_enable() is invoked with a one-byte receive buffer (len == 1) and CONFIG_UART_MCHP_ASYNC is enabled, the RX-complete ISR starts a single-beat DMA transfer while a received byte is already pending in the SERCOM DATA register. On this SoC the peripheral-triggered DMA start sequencing then writes one byte past the end of the caller-supplied buffer (CWE-787). The overflowed byte's value is the UART RX data supplied by the connected serial peer (adjacent attacker), while its size and location are fixed at one byte immediately after the buffer. Exploitation requires the async UART config (not enabled by default on the in-tree PIC32CM-JH boards) and a consumer that enables RX with a one-byte buffer; impact is limited single-byte memory corruption adjacent to the RX buffer (possible crash / denial of service). The defect shipped in v4.4.0. The fix reads the first byte with the CPU and, for one-byte buffers, performs no DMA at all; for larger buffers it sizes the DMA for the remaining len-1 bytes.

Zephyr's IPv6 network stack can be prevented from receiving or processing future incoming packets by sending a small number of maliciously fragmented IPv6 packets. When such a packet is handled by the fragment-header processing path, the associated RX network packet buffer (allocated from a memory slab) is not released back to the pool. Repeating the malicious packet exhausts all RX buffer slots, after which the device can no longer obtain RX buffers and stops receiving traffic, resulting in a denial of service.

The Zephyr PL011 UART driver (drivers/serial/uart_pl011.c) contains an unbounded software loop in pl011_irq_tx_enable() that repeatedly invokes the interrupt-driven application callback while the TX interrupt mask bit (PL011_IMSC_TXIM) is set, to work around the controller's level-transition TX-interrupt behavior. When CTS hardware flow control is enabled (devicetree hw-flow-control or runtime UART_CFG_FLOW_CTRL_RTS_CTS) and the wired serial peer de-asserts CTS, the controller stops draining the TX FIFO; pl011_fifo_fill() then returns 0 on every call while the application still has pending data and therefore never disables the TX interrupt. The loop condition never clears, so the thread that called uart_irq_tx_enable() (e.g. h4_send() in the Bluetooth HCI H4 driver) spins indefinitely, hanging the executing context and stalling the transport — a denial of service (CWE-835). An attacker controlling the device attached to the UART's CTS line can trigger the hang by withholding CTS during transmission. Impact is availability only; there is no memory-safety, confidentiality, or integrity consequence. The vulnerable loop was introduced in commit b783bc8448ef (Feb 2025) and shipped in releases v4.1.0 through v4.4.0. The fix breaks out of the loop when CTS is blocking and arms the CTS modem-status interrupt to resume transmission when CTS re-asserts.

A missing length validation in the Zephyr Bluetooth Host ISO receive path can be triggered by malformed HCI ISO data. In bt_iso_recv() (subsys/bluetooth/host/iso.c), when processing PB=START/SINGLE fragments, the code pulls a TS SDU header (8 bytes, ts=1) or a non-TS SDU header (4 bytes, ts=0) without first verifying that buf->len contains at least that many bytes. The outer HCI ISO length check in hci_iso() validates payload length consistency but not the minimum inner SDU header size, so a packet with payload length 1 passes hci_iso() and then reaches net_buf_pull_mem(), which asserts buf->len >= len. As a result, malformed ISO traffic deterministically triggers a kernel assert (denial of service) in assert-enabled builds, and in non-assert builds the same path may proceed with an undersized buffer, leading to out-of-bounds read behavior. The issue affects products using the Zephyr Host with CONFIG_BT_ISO_RX enabled, particularly where incoming HCI data can be influenced by a malicious or compromised controller or malformed forwarded ISO traffic.

A malformed Bluetooth Classic SDP attribute can trigger a reachable assertion in Zephyr's SDP parser. In subsys/bluetooth/host/classic/sdp.c, bt_sdp_parse_attribute() accepts an input buffer once it contains the 1-byte attribute type and 2-byte attribute id, but then unconditionally pulls an additional byte for the value type without verifying that the byte is present. A truncated 3-byte attribute (for example 09 00 09) therefore reaches net_buf_simple_pull() with insufficient remaining length, triggering the __ASSERT_NO_MSG(buf->len >= len) check and a kernel panic in assert-enabled builds (denial of service). In builds where assertions are disabled, parsing may continue past the end of the available buffer, leading to an out-of-bounds read and undefined behavior.

Zephyr's ext2 directory-entry parser does not fully validate on-disk directory entry structure before copying the entry name and advancing traversal state. In ext2_fetch_direntry() (subsys/fs/ext2/ext2_diskops.c), the code only checks de_name_len <= EXT2_MAX_FILE_NAME and then copies the name with memcpy without validating the structural relationship between de_rec_len, de_name_len, and the directory block boundary (for example that de_rec_len is non-zero, at least the size of the entry header, and that the record fits within the block). Callers such as find_dir_entry() and ext2_get_direntry() (subsys/fs/ext2/ext2_impl.c) then advance traversal using the unvalidated de_rec_len. A crafted ext2 image can therefore cause an out-of-bounds read from the directory block buffer when a malformed entry near the end of a block triggers an oversized name copy, or a zero-progress infinite loop when de_rec_len == 0. The issue is not reached at mount time but later through directory traversal paths such as pathname lookup, stat/open/unlink/rename, and readdir. The primary impact is denial of service and out-of-bounds reads under attacker-controlled ext2 images mounted from untrusted media.

The SocketCAN implementation validates the length of a user-provided buffer containing a socketcan_frame object using only a NET_ASSERT statement in zcan_sendto_ctx() before dereferencing it in socketcan_to_can_frame(). In production builds where assertions are disabled, a userspace application that controls the length passed to a sendto syscall can supply an incomplete or truncated frame, causing socketcan_to_can_frame() to dereference fields beyond the end of the buffer. This results in an out-of-bounds read that can cause denial-of-service crashes or, because the parsed frame contents are transmitted on the network, leak adjacent memory.

A bitwise shift vulnerability in Zephyr's PTP subsystem allows a remote attacker to cause undefined behavior and potential system crashes. An attacker sends a crafted PTP_MSG_MANAGEMENT message to set an unvalidated negative log_announce_interval value in the port's data set. When a subsequent PTP_MSG_ANNOUNCE message is processed, port_timer_set_timeout_random computes a timeout as NSEC_PER_SEC >> -log_seconds; if the attacker-supplied value is sufficiently negative (e.g., -127), the shift amount exceeds the 64-bit integer width, triggering undefined behavior in C. This can cause a system crash via a compiler-generated illegal instruction trap on some architectures, or produce an erroneous zero timeout leading to resource starvation loops or other logical errors.